any rev made to this print must have an updated mkt print do not scale from this print .134 .003 3.41 0.08 .104 ref 2.64 .012 0.31 (see note 9) "a" "a" item no. part number quantity material 1 asp-103597-01-b 1.0000 ul 94 v0, color: black 2 c-140-03-h 114.00 phos bronze, 521 hard temper 3 sdb-030-6337 114.00 63% tin /37% lead 4 ty-yfs004-19-3-6 .01539 conductive polymer .145 3.68 ref .095 2.41 ref .970 ref 24.64 1.070 ref 27.18 .320 ref 8.13 .035 ref 0.89 .900 .002 22.86 0.05 (18 pos x .0500[1.270]) .250 6.35 a b c d e f 01 19 section "a"-"a" 1 2 3 critical dimension inspection instruction table assembly operation in process inspection fill c-140-03-h c2, c3 attach sdb-030-6337 c3 finished good inspection c1, c3 sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 2 .xxx: .005 .xxxx: .0020 vita 42 (lead free) socket assembly by: ASP-103612-03 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing j lackey 10/18/2006 2 1 sheet scale: 3:1 f:\dwg\misc\mktg\ASP-103612-03-mkt.slddrw plating: contact area: .000030 gold over .000050 nickel remainder: .000003 flash gold over .000050 nickel notes: 1. use asp-103597-01-b body for non-standard 19 position. 2. represents a critical dimension. 3. burr allowance: .0005[0.013] max. 4. minimum pushout force: .5 lb. 5. maximum allowable bow: .002[0.05] inch/inch after assembly. 6. contact to be flush +/-.002 . 7. one reel minimum plating requirement (85,000 contacts per reel). 8. all dims to be symmetrical about the centerline within .001[0.03]. 9. .0025[0.064] max variation between solderballs. 10. refer to visual inspection board for solderball appearance checks. 11. the distance from the center of any solderball to the center of any adjacent inner peg shall be .025.005[0.640.13]. 12. parts to be packaged in trays. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision h
.2500 6.350 .9000 22.860 "a" recommended board layout 01 19 .0100 0.254 trace .0250 0.635 .0200 0.508 pad .0100 0.254 via (plated) .0250 0.635 pad .0310 0.787 free of solder mask 45 detail "a" scale 12 : 1 .900 22.86 .050 1.27 (typ) .250 6.35 .050 1.27 (typ) .0250 0.635 (typ) 01 19 recommended stencil layout stencil to be .0060[0.152] thick a b c d e f note: outer rows may not need vias - this is left to the discretion of the board designer. a b c d e f sheet of vita 42 (lead free) socket assembly by: ASP-103612-03 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. j lackey 10/18/2006 2 2 sheet scale: 3:1 ASP-103612-03 f:\dwg\misc\mktg\ASP-103612-03-mkt.slddrw revision h 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
